The Outsunny 8.8 ft Solar Powered Outdoor Patio Umbrella (SKU: 840-125CG) is designed for outdoor use in gardens, patios, terraces, or by swimming pools. It features 24 pre-installed LED lights (3 per rib) with four adjustable colour options red, blue, green, and warm light powered by a top-mounted solar panel.
The round canopy is made from 180-GSM polyester fabric, supported by a powder-coated steel frame with eight ribs and a vented top to help improve airflow and stability during use.
Estimated Assembly Time: Approx. 10 minutes
Recommended People: 1–2 adults
Tools Recommended
- No specific assembly tools are required
- Soft cloth (for cleaning the solar panel)
- Protective gloves (recommended if handling a leaking battery)
Parts List
- A – Upper Umbrella Frame with Canopy
- B – Lower Support Pole
- C – Solar Panel Unit
Hardware List
- Rechargeable Battery (pre-installed, replaceable)
- Battery Compartment Cover (located on the unit)
Safety Instructions
- Do not use the umbrella during extreme weather conditions such as strong wind, heavy rain, or snow.
- Always secure the umbrella to a suitable weighted base or patio table before use (base not included).
- Keep the product away from heat sources and open flames.
- Adult supervision is required when replacing or disposing of rechargeable batteries.
- This product is not a toy; keep it out of reach of small children.
- Do not attempt to modify or repair the umbrella yourself; contact customer service if damage occurs.
Assembly Instructions
Follow the steps below carefully to ensure correct assembly, stable operation, and proper lighting functionality for your Outsunny 8.8 ft Solar Powered Outdoor Patio Umbrella.
Step 1: Connect the Umbrella Frame, Pole, and Solar Panel
- Identify the Upper Umbrella Frame (A), Lower Support Pole (B), and Solar Panel Unit (C).
- Align the bottom connector of the upper umbrella frame (A) with the top opening of the lower support pole (B).
- Press the spring button marked “PUSH” on the lower support pole (B) and slide it into the upper umbrella frame (A) until it clicks and locks into place.
- Place the Solar Panel Unit (C) onto the top of the umbrella frame.
- Rotate and press the solar panel in the direction shown in the diagram until it is fully seated and secure.
Step 2: Open the Umbrella and Set the LED Light Mode
- Turn the integrated crank handle on the pole in the direction shown to gradually open the umbrella canopy.
- Continue cranking until the canopy is fully extended and the fabric is taut, ensuring the ribs are evenly aligned.
- Locate the LED control button on the pole or rib, as indicated in the diagram.
- Press the button to cycle through the four available light colours: red, blue, green, and warm light.
- To test the lights, ensure the solar panel is in a dark area or covered, as the LEDs are designed to turn on automatically at dusk.
Step 3: Adjust the Umbrella Tilt Angle
- Locate the tilt button on the upper section of the umbrella pole.
- Press and hold the button marked “PUSH” to unlock the tilt mechanism.
- While holding the button, gently tilt the umbrella canopy in the direction needed for shade.
- Adjust the canopy gradually until the desired tilt angle is reached.
- Release the button to lock the canopy securely in position.
- Check that the tilt mechanism is fully engaged and the canopy does not move freely.
Step 4: Adjust the Umbrella Tilt to the Opposite Side
- Locate the tilt button on the upper section of the umbrella pole as shown above.
- Press and hold the button marked “PUSH” to release the tilt mechanism.
- While holding the button, gently tilt the umbrella canopy toward the opposite side.
- Move the canopy slowly until the desired tilt angle is reached.
- Release the button to lock the canopy securely in the new position.
- Check that the canopy remains stable and does not shift after releasing the button.
Step 5: Close the Umbrella and Complete Assembly
- Locate the crank handle on the umbrella pole, as shown in the diagram.
- Turn the crank handle slowly in the opposite direction to begin closing the umbrella canopy.
- Continue cranking until the canopy folds evenly around the pole.
- Ensure all ribs move inward smoothly and align properly during closing.
- Fully close the umbrella until the fabric hangs neatly without twisting.
Final Step
- Fully retract the canopy using the crank handle when not in use.
- Ensure the fabric is completely dry before closing to prevent moisture buildup.
- Store the umbrella in a dry, well-ventilated area when not in use for extended periods.
Usage Tips
- Clean the solar panel surface regularly to maintain charging efficiency.
- Use a protective umbrella cover to extend fabric and LED lifespan.
- Retract the umbrella immediately during windy conditions.
Maintenance & Care
- Wipe the frame with a soft, damp cloth.
- Clean the polyester canopy using warm water and mild soap only.
- Avoid abrasive cleaners or harsh chemicals.
- Replace the rechargeable battery as needed to maintain consistent lighting performance.
- Periodically check for loose parts, wear, or corrosion.
Ready for Use
Your Outsunny 8.8 ft Solar Powered Outdoor Patio Umbrella is now fully assembled and ready to use. With proper care and regular charging, it will provide reliable shade during the day and ambient lighting at night.
You can also download the Outsunny 8.8 ft Solar Powered Outdoor Patio Umbrella (SKU: 840-125CG) for your reference.
Need Assistance?
If you have any questions about the product, warranty, returns, or general use, please contact Aosom Customer Support for assistance.
FAQs
Remove the battery compartment cover, take out the old battery, and insert a new rechargeable battery of the same or equivalent type, ensuring correct polarity.
Avoid direct contact with leaked fluid. Wear protective gloves, seal the battery in a bag, and dispose of it at a proper hazardous waste facility.
Nearby light sources such as street or porch lights can interfere with the sensor. Place the umbrella in a darker area at night for proper operation.