Outsunny Outdoor Loveseat with Glass Table Manual (SKU: 83B-248V00BN)

Enjoy comfort and style with this Outsunny Outdoor Loveseat, featuring two mesh seats and a sleek glass table. Perfect for outdoor relaxation, it offers durable steel construction and a chic water ripple glass top.

Helpful Tips for Using Your Loveseat

• Put the chair stably on a flat floor.
• Mount the garden chairs in the shelter of the weather.
• Stay away from open flames.
• Don’t hang anything in the structure.
• Avoid overload at the anchors/structure.
• It is advised that you don’t stay on the chairs when there is a storm.
• Do not use it in adverse weather conditions and cover the furniture when not in use.

Parts List

• 1 – Left Front Frame (x1)
• 2 – Right Front Frame (x1)
• 3 – Left Back Frame (x1)
• 4 – Right Back Frame (x1)
• 5 – Chair Support Bar (x4)
• 6 – Middle Connecting Support Bar (x1)
• 7 – Left Seat (x1)
• 8 – Right Seat (x1)
• 9 – Backrest (x2)
• 10 – Middle Table Top (x1)

Hardware List

• 11 – M615 Bolts (x20)
• 12 – M625 Bolts (x14)
• 13 – M6*30 Bolts (x4)
• 14 – Washers Φ6 (x42)
• 15 – M6 Nuts (x4)
• 16 – Allen Key (x1)
• 17 – Wrench (x1)

Precautions Before Assembly

1. Prepare a clean and dry mounting area.
2. Verify that the product is not damaged and all parts are included before beginning the assembly.
3. Clean fabric surfaces with a soft fabric to avoid any dirt or moisture buildup that could affect the assembly or performance of the furniture.
4. Avoid assembly during adverse weather conditions, and ensure the furniture is assembled on a stable surface.

Assembly Instructions

Follow the step-by-step assembly instructions below to easily set up your Outsunny Outdoor Loveseat with Glass Table (SKU: 83B-248V00BN).

Step 1: Attach the Front Frames with Support Bars

Parts Used

• 1 – Left Front Frame (x1)
• 2 – Right Front Frame (x1)
• 5 – Chair Support Bar (x2)

Hardware Used

• 11 – M6*15 Bolts (x4)
• 14 – Washers Φ6 (x4)
• 16 – Allen Key (x1)

Instructions

1. Place the Left Front Frame (1) and Right Front Frame (2) upright on a flat surface, keeping them parallel.
2. Position one Chair Support Bar (5) between the frames at the upper connection points.
3. Align the holes and insert M6*15 Bolts (11) with Washers Φ6 (14) through the frame and support bar.
4. Repeat the same process to attach the second Chair Support Bar (5) at the lower connection points.
5. Lightly tighten all bolts using the Allen Key (16). Do not fully tighten yet to allow adjustment in later steps.

Ensure both frames remain level and evenly spaced before moving to the next step.

Step 2: Install the Left Seat

Parts Used

• 7 – Left Seat (x1)

Hardware Used

• 12 – M6*25 Bolts (x4)
• 14 – Washers Φ6 (x4)
• 16 – Allen Key (x1)

Instructions

1. Place the Left Seat (7) onto the assembled frame, aligning the seat mounting holes with the frame holes.
2. Insert an M6*25 Bolt (12) with a Washer Φ6 (14) into each hole.
3. Tighten all bolts lightly using the Allen Key (16).
4. Do not fully tighten at this stage to allow adjustment in later steps.

Ensure the seat panel sits flat and evenly supported before continuing.

Step 3: Attach the Backrest

Parts Used

• 9 – Backrest (x1)

Hardware Used

• 12 – M6*25 Bolts (x2)
• 13 – M6*30 Bolts (x2)
• 14 – Washers Φ6 (x4)
• 15 – M6 Nuts (x2)
• 16 – Allen Key (x1)
• 17 – Wrench (x1)

Instructions

1. Position the Backrest (9) onto the rear of the installed seat, aligning it with the pre-assembled frame holes.
2. Insert M6*25 Bolts (12) with Washers Φ6 (14) on one side and tighten lightly.
3. Insert M6*30 Bolts (13) with Washers Φ6 (14) on the opposite side, secure with M6 Nuts (15), and tighten lightly.
4. Use the Allen Key (16) and Wrench (17) to secure the fasteners, keeping the backrest straight.
5. Do not fully tighten the bolts until all assembly steps are completed.

Make sure the backrest is upright and evenly aligned.

Step 4: Secure the Two Seats Together

Parts Used

• 6 – Middle Connecting Support Bar (x1)

Hardware Used

• 12 – M6*25 Bolts (x2)
• 14 – Washers Φ6 (x2)
• 16 – Allen Key (x1)

Instructions

1. Position the Middle Connecting Support Bar (6) between the Left Seat (7) and Right Seat (8), aligning it with the mounting holes on both seats.
2. Insert an M6*25 Bolt (12) with a Washer Φ6 (14) through each side of the support bar.
3. Tighten the bolts lightly using the Allen Key (16).
4. Ensure both seats are evenly aligned before proceeding.

Do not fully tighten the bolts until all remaining assembly steps are completed.

Step 5: Attach the Middle Table Frame

Parts Used

• 10 – Middle Table Top(x1)

Hardware Used

• 11 – M6*15 Bolts (x4)
• 14 – Washers Φ6 (x4)
• 16 – Allen Key (x1)

Instructions

1. Place the Middle Table Top(10) between the two installed seats, aligning it with the mounting holes on each side.
2. Insert an M6*15 Bolt (11) with a Washer Φ6 (14) into each mounting hole.
3. Tighten the bolts evenly using the Allen Key (16).
4. Check that the table frame is centred and level between both seats.

Once aligned, fully tighten all previously installed bolts to complete the assembly.

Final Step – Completed Assembly

Your Outsunny Outdoor Loveseat is now fully assembled. Both chairs and the table are securely connected. Enjoy your new outdoor seating setup!

Maintenance Instructions

• Clean regularly using a soft, damp cloth.
• Store in a dry, cool place to avoid moisture buildup.
• Check bolts and nuts regularly to ensure they remain secure. 

Storage Instructions

• When not in use, store the furniture in a dry, cool environment to avoid potential mold buildup.
• Avoid storing under direct sunlight for prolonged periods to prevent fabric fading.

Thank you for choosing the Outsunny Outdoor Loveseat with Glass Table (SKU: 83B-248V00BN). With proper assembly and care, your loveseat will provide lasting comfort and enhance your outdoor space. For assistance, replacement parts, or questions, Aosom Customer Support is here to help.

You can also download the Outsunny Outdoor Loveseat Manual for your reference.

FAQs

1. The loveseat feels unstable after assembly. What could be the problem?

Ensure all bolts are securely tightened and check for any misalignment in the frame. If the loveseat is on uneven ground, adjust the placement to make sure it’s on a flat, stable surface to prevent wobbling.

2. The glass tabletop is loose or doesn’t sit flush with the frame. How can I fix this?

Check that the Table Top (10) is properly aligned with the seat frames before tightening the bolts. Tighten each bolt evenly to ensure the table is secured and sits flush with the frames, preventing any shifting.

3. The backrest is not sitting properly on the frame. How can I adjust it?

Recheck the alignment of the Backrest (9) with the Armrest Frame (2) and Support Bar (7). Slightly adjust the backrest to ensure the holes align, and then securely tighten the bolts to fix it in place.