The HOMCOM Farmhouse Coffee Table combines a solid wood structure with a tempered glass tabletop and a practical lower storage shelf. The cross-braced side frames enhance stability, while the cam-lock system allows secure and precise assembly. Following each step in sequence ensures proper alignment, strength, and long-term everyday use.
⚠️ Warning & Safety Instructions
Before beginning assembly, carefully review the following safety guidelines:
- For indoor household use only
- Assemble on a clean, flat, and stable surface
- Keep children and pets away during assembly
- Do not use the product if any part is damaged or missing
- Do not overtighten cam locks or connector bolts
- Handle the tempered glass tabletop with care
Unboxing Your Coffee Table: What’s Included
Remove all components from the package and confirm that all parts and hardware listed below are present before starting assembly.
Parts List
| No. | Part Name | Quantity |
| 1 | Tabletop Frame | 1 |
| 2 | Side Frame Panels | 2 |
| 3 | Bottom Shelf Panel | 1 |
| 4 | Long Side Rails | 2 |
| 5 | Short Side Rails | 2 |
| 6 | Tempered Glass Tabletop | 1 |
Hardware List
| Code | Hardware | Quantity |
| A | Ø6×30 Wooden Dowels | 16 (+2 spare) |
| B | Cam Connector Bolts | 28 (+2 spare) |
| C | Cam Lock Nuts | 28 (+2 spare) |
| D | Screwdriver | 1 |
All required tools are included.
Step-by-Step Assembly Instructions
When assembling your Farmhouse Coffee Table ,(SKU: 833-949) please follow these steps carefully to ensure a smooth assembly process.
Step 1: Insert Wooden Dowels into the Bottom Shelf Panel
- Place the Bottom Shelf Panel (3) flat on the floor with the drilled holes facing upward, as shown in the diagram.
- Identify the Ø6×30 Wooden Dowels (A) and confirm the required quantity for this step.
- Insert each wooden dowel straight into the pre-drilled holes along the edges of the shelf panel.
- Push the dowels in firmly by hand until they sit securely inside the holes.
- Make sure all dowels are evenly inserted and remain perpendicular to the panel edges.
- Double-check that no dowel is loose or angled before proceeding to the next step.
Step 2: Prepare the Long and Short Side Rails
- Identify the Long Side Rails (4) and Short Side Rails (5) and place them flat on a clean surface as shown.
- Insert Ø6×30 Wooden Dowels (A) into the pre-drilled holes of each Short Side Rail (5), ensuring they are pushed in straight.
- Insert Cam Connector Bolts (B) into the designated holes on each Long Side Rail (4).
- Make sure the heads of the cam connector bolts face upward and align correctly with future cam-lock positions.
- Repeat this process so that both long rails and both short rails are prepared identically.
- Check that all dowels and bolts are fully seated and properly aligned before moving to the next step.
Step 3: Attach the Long Side Rails to the Bottom Shelf Panel
- Place the Bottom Shelf Panel (3) flat on the floor with the cam holes facing upward, as shown in the diagram.
- Insert the Cam Lock Nuts (C) into the pre-drilled cam holes on the shelf panel, making sure the arrow or opening faces the bolt entry direction.
- Position the prepared Long Side Rails (4) along both long edges of the shelf panel.
- Align the cam connector bolts on the rails with the cam lock nuts installed in the shelf panel.
- Slide the rails into position so the bolts fully enter the cam locks.
- Turn each cam lock clockwise until tight, securing both long side rails firmly to the shelf panel.
Step 4: Prepare the Side Frame Panels
- Place each Side Frame Panel (2) upside down on a flat, stable surface as shown in the diagram.
- Insert Ø6×30 Wooden Dowels (A) into the pre-drilled holes located on the inner sides of each frame.
- Insert Cam Connector Bolts (B) into the designated top mounting holes on each side frame.
- Ensure all cam connector bolts are inserted straight and seated fully.
- Repeat the same preparation process for the second side frame panel.
- Check that all dowels and bolts are correctly positioned before proceeding.
Step 5: Connect the Shelf Assembly to the Side Frame Panels
- Position the two Side Frame Panels (2) upright on a flat surface, facing inward as shown.
- Lift the assembled Bottom Shelf Panel (3) with attached Long Side Rails (4) and Short Side Rails (5).
- Align the cam connector bolts on the shelf assembly with the corresponding cam holes on both side frame panels.
- Insert Cam Lock Nuts (C) into all exposed cam holes along the connection points.
- Carefully slide the shelf assembly into place between the side frames so all bolts enter the cam locks.
- Turn each cam lock clockwise until fully tightened, securing the shelf assembly firmly to both side frame panels.
Step 6: Prepare the Tabletop Frame
- Place the Tabletop Frame (1) upside down on a clean, flat surface as shown.
- Identify the Cam Connector Bolts (B) required for this step.
- Insert one cam connector bolt into each pre-drilled hole along the inner edges of the tabletop frame.
- Ensure all bolts are inserted straight and fully seated.
- Check that the bolt heads are oriented correctly for later cam-lock connections.
- Confirm all connector bolts are evenly installed before moving to the next step.
Step 7: Attach the Tabletop Frame to the Base Assembly
- Position the assembled base with the Side Frame Panels (2) standing upright on a flat surface.
- Carefully lower the prepared Tabletop Frame (1) onto the top of the base assembly, aligning it as shown.
- Insert Cam Lock Nuts (C) into all visible cam holes along the inner sides of the base structure.
- Ensure each cam lock aligns with the cam connector bolts installed in the tabletop frame.
- Turn all cam locks clockwise until fully tightened to secure the tabletop frame to the base.
- Check that the tabletop frame sits evenly and firmly on the base before proceeding.
Step 8: Install the Tempered Glass Tabletop and Complete Assembly
- Carefully lift the Tempered Glass Tabletop (6) using both hands, keeping it level.
- Align the glass panel above the opening in the Tabletop Frame (1) as shown.
- Lower the glass straight down into the recessed frame opening.
- Ensure the glass sits evenly on all sides and rests flat within the frame.
- Do not slide, force, or tilt the glass once it is placed.
- Visually confirm the table is fully assembled and stable before use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Table feels unstable | Cam locks not fully tightened | Retighten all cam locks evenly |
| Shelf sits unevenly | Frame not squared during assembly | Loosen, realign, retighten |
| Gaps between rails | Dowels not fully inserted | Reinsert dowels and reconnect |
| Glass does not sit flat | Frame misalignment | Recheck tabletop frame alignment |
Care & Maintenance
- Clean wooden surfaces with a dry or slightly damp cloth
- Clean glass with a soft cloth and glass cleaner
- Avoid abrasive cleaners or harsh chemicals
- Periodically check cam fittings and retighten if needed
- Do not place excessive weight on the glass surface
With its farmhouse-inspired design, tempered glass top, and functional lower shelf, the HOMCOM Farmhouse Coffee Table (SKU: 833-949) offers everyday practicality with a clean, structured appearance. Proper assembly ensures lasting stability and reliable performance.
You can also download the official HOMCOM Farmhouse Coffee Table assembly manual (PDF) for reference.
For technical support, replacement parts, or product questions, you can reach out any time.
FAQs
This usually happens when the cam connector bolt is not aligned correctly with the cam lock. Loosen the parts slightly, realign the panels, and try again. Forcing the cam can damage the fitting.
A slight rattle is often caused by uneven frame alignment rather than the glass itself. Check that the tabletop frame is fully tightened and sitting square. Once aligned, the glass should rest securely without movement.
Uneven flooring is the most common cause of wobbling after assembly. Move the table slightly to find a level spot and retighten all cam locks evenly. Avoid using shims until all joints are properly secured.