HOMCOM 39″ Upholstered Ottoman Bench with Padded Seat Assembly Manual SKU: 831-908V00GN

The HOMCOM 39″ Upholstered Ottoman Bench (SKU: 831-908V00GN) is designed to bring comfortable, modern seating to bedrooms, entryways, living rooms, and window-side spaces. Built with a thick 13 cm padded top wrapped in soft corduroy fabric and supported by strong powder-coated steel legs, it offers a sturdy, stylish place to sit, relax, or put on shoes. 

Its streamlined tufted design blends effortlessly with contemporary décor, while the solid frame supports up to 485 lbs for everyday use. Whether used as an end-of-bed bench, hallway seating, or an accent piece in your home, this versatile bench adds warmth, texture, and practical comfort to any room.

Before You Begin

Estimated Assembly Time: 10–15 minutes
Recommended Personnel: 1–2 adults
Assembly Surface: Work on a clean, flat, soft surface to protect the corduroy fabric and prevent scratches to the steel legs.

Safety Precautions

• Assemble the bench on a flat, stable, clean surface to ensure proper alignment.
• Keep children and pets away from the assembly area to avoid contact with loose hardware or tools.
• Do not exceed the maximum weight capacity of 485 lbs (220 kg) to prevent structural stress or damage.
• Keep fingers clear of mounting areas during assembly to avoid pinching injuries.
• Avoid placing the bench near open flames, heaters, or sharp objects that may damage the upholstery.
• Always lift the bench when moving it, dragging can loosen hardware or strain the leg joints.

Parts & Hardware 

Parts List

Label	Quantity	Name / Description
D	4	Bench Legs
E	1	Upholstered Bench Body

Hardware List

Label	Quantity	Description
A	16 (+2 spare)	M6×20mm Bolts
B	16 (+2 spare)	M6×16mm Washers
C	1	Allen Key

Assembly Instructions

Follow these steps carefully and proceed sequentially to assemble your Upholstered Ottoman Bench with Padded Seat (SKU: 831-908V00GN)

Step 1: Attach the First Bench Leg to the Seat Base

This step requires the following parts and hardware:
M6×20mm Bolts – A (x4)
M6×16mm Washers – B (x4)
Allen Key – C (x1)

Bench Leg – D (x1)
Upholstered Bench Body – E (x1)

Instructions:

1. Place the Upholstered Bench Body (E) upside down on a clean, flat surface, exposing the mounting holes on the underside.
2. Position one Bench Leg (D) over one set of pre-drilled holes, aligning the plate at the top of the leg with the bracket on the bench frame.
3. Insert an M6×20mm Bolt (A) with an M6×16mm Washer (B) into each hole.
4. Using the Allen Key (C), tighten each bolt lightly to secure the leg in place.
5. Do not fully tighten the bolts yet, leave them slightly loose to allow for adjustment when installing the remaining legs.

Step 2: Attach the Remaining Bench Legs

This step requires the following parts and hardware:
M6×20mm Bolts – A (x12)
M6×16mm Washers – B (x12)
Allen Key – C (x1)

Bench Legs – D (x3 remaining)
Upholstered Bench Body – E (x1, already positioned)

Instructions:

1. With the bench body (E) still positioned upside down, align the second Bench Leg (D) with the next set of pre-drilled holes.
2. Insert an M6×20mm Bolt (A) paired with an M6×16mm Washer (B) into each mounting hole.
3. Lightly tighten the bolts using the Allen Key (C), ensuring the leg sits firmly but still allows slight adjustment.
4. Repeat this process for the third and fourth Bench Legs (D), attaching each one to the remaining mounting brackets on the frame.
5. Once all four legs are installed and aligned, use the Allen Key (C) to tighten every bolt securely and evenly.

Step 3: Finalize the Assembly and Set the Bench Upright

Instructions:

1. After attaching all four legs in the previous steps, double-check that every bolt is firmly tightened.
2. Carefully flip the bench upright and place it on a flat, stable surface.
3. Press down gently on different areas of the bench to ensure it sits evenly and does not wobble.
4. Make any final minor adjustments if needed to ensure full stability.

Care & Maintenance

• Wipe the corduroy fabric and steel legs with a soft, damp cloth to remove dust and everyday dirt.
• Avoid bleach, harsh chemicals, or abrasive scrubbing tools that may damage the upholstery or scratch the powder-coated legs.
• Blot spills immediately and allow the fabric to dry fully to prevent stains or moisture damage.
• Keep the bench in a dry indoor location to avoid mold or fabric deterioration.
• Periodically check all bolts and connection points, especially after moving the bench or placing it on carpet, and tighten if needed.
• Lift the bench when relocating it, dragging may loosen the legs or damage the floor.

Ready to Use!

Your HOMCOM 39″ Upholstered Ottoman Bench is now fully assembled and ready to enhance your living space with comfort and style. Whether placed at the end of your bed, positioned in the entryway for putting on shoes, or used as additional seating in the living room, this bench adds a modern, functional touch to any room.

With its soft corduroy upholstery, thick padded top, and sturdy steel legs, it offers dependable everyday support and a refined look. Set it in your desired location and enjoy the comfort and versatility it brings to your home.

Keep the Upholstered Ottoman Bench with Padded Seat SKU: 831-908V00GN assembly PDF manual on hand for future adjustments, seasonal maintenance, or reassembly when needed.

For technical support, replacement parts, or product-related assistance, feel free to contact Aosom Customer Service for fast and friendly help.

FAQs

1. Why does my bench feel uneven on a tile or hardwood floor?

Slight unevenness often comes from minor floor inconsistencies rather than the bench itself. Try shifting the bench to another spot or adding small felt pads under the leg that sits higher. This usually balances the bench immediately.

2. My bench moves slightly when I sit down. How can I stabilize it?

Movement typically occurs when the bench is placed on smooth flooring. Adding non-slip pads under each leg increases grip and prevents shifting without damaging the floor.

3. What should I do if one bolt keeps turning but doesn’t tighten fully?

Remove the bolt, realign the leg plate, and reinsert it straight into the threaded hole. A misaligned angle prevents proper tightening, but reseating the bolt usually solves the issue.