Outsunny 2 Pieces Outdoor Glider Chairs Assembly Manual SKU: 84B-776

The Outsunny 2-Piece Outdoor Glider Chair Set features breathable mesh fabric seating supported by a durable powder-coated steel frame. Designed for smooth, stable gliding motion, each chair supports up to 120 kg (264 lbs) and is suitable for patios, decks, balconies, and garden spaces.

Parts List (Per Chair)

Part ID	Quantity	Description
A	x1	Left Armrest Frame
B	x1	Right Armrest Frame
C	x2	Horizontal Base Connecting Bars
D	x2	Glider Link Arms
E	x1	Seat & Backrest Assembly
F	x1	Front Base Frame
G	x1	Rear Base Frame
H	x2	M6 Open-End Spanner

Hardware List (Per Chair)

Code	Quantity	Description
I	x4	M6×15 Bolts
J	x2	M6×40 Bolts
K	x4	M6×45 Bolts
L	x6 (+1 spare)	M6×50 Bolts
M	x4	M6×60 Bolts
N	x14 (+1 spare)	M6 Nuts
O	x20 (+1 spare)	M6 Washers
P	x4	Small Spacers
Q	x4	Medium Spacers
R	x2	Large Spacers
S	x1	Allen Key

Safety Information

• Do not fully tighten bolts until all parts are connected.
• Assemble on a flat, stable surface.
• Keep children away during assembly.
• Do not exceed 120 kg (264 lbs) per chair.
• Inspect and retighten hardware periodically.
• Avoid use during extreme weather conditions.

Assembly Instructions

When assembling your 2 Pieces Outdoor Glider Chairs, follow the steps carefully to ensure a smooth and hassle-free assembly process.

Step 1: Assemble the Base Frame Structure

Parts Used:

• F: Front Base Frame (x1)
• G: Rear Base Frame (x1)
• C: Horizontal Base Connecting Bars (x2)

Hardware Used:

• I: M6 × 15 Bolts
• J: M6 × 40 Bolts
• O: M6 Washers
• N: M6 Nuts

Instructions:

1. Place the Front Base Frame (F) and Rear Base Frame (G) on a flat surface facing each other.
2. Insert the two Connecting Bars (C) between the upper and lower mounting points.
3. Align all holes properly before inserting bolts.
4. For upper holes, insert Bolts I (M6 × 15) with Washer O.
5. For lower holes, insert Bolts J (M6 × 40), add Washer O, and secure with Nut N.
6. Tighten hardware to about 75% only.
7. Do not fully tighten at this stage to allow later adjustment.

This step forms the lower base foundation of the glider chair.

Step 2: Install the Glider Link Arms

Parts Used:

• D: Glider Link Arms (x2)
• G: Rear Base Frame (from Step 1)
• C: Horizontal Base Connecting Bars (from Step 1)

Hardware Used:

• K: M6 × 45 Bolts
• L: M6 × 50 Bolts
• O: M6 Washers
• N: M6 Nuts
• P: Small Spacers

Instructions:

1. Position one Glider Link Arm (D) on each side of the base frame.
2. Align the upper mounting hole of D with the hole on the Rear Base Frame (G).
3. Insert Spacer P between the pivot connection points as shown.
4. Insert Bolt K (M6 × 45) through the aligned holes.
5. Add Washer O and secure with Nut N.
6. Align the lower end of D with the lower base mounting point.
7. Insert Bolt L (M6 × 50), add Washer O, and secure with Nut N.
8. Repeat the same process on the opposite side.
9. Tighten to approximately 75% only.

Step 3: Attach the Side Armrest Frames

Parts Used:

• A: Left Armrest Frame (x1)
• B: Right Armrest Frame (x1)
• D: Glider Link Arms (installed in Step 2)

Hardware Used:

• L: M6 × 50 Bolts
• O: M6 Washers
• N: M6 Nuts
• Q: Medium Spacers

Instructions:

1. Position the Left Armrest Frame (A) and Right Armrest Frame (B) upright on each side of the base structure.
2. Align the mounting holes of the armrest frames with the upper pivot holes of the Glider Link Arms (D).
3. Insert Spacer Q between the pivot connection points as shown in the diagram.
4. Insert Bolt L (M6 × 50) through the aligned holes and spacer.
5. Add Washer O and secure with Nut N on the opposite side.
6. Repeat the process for the opposite side.
7. Tighten to approximately 75% only.
8. Do not fully tighten at this stage to allow alignment in the next step.

Step 4: Install the Seat & Backrest Assembly

Parts Used:

• E: Seat & Backrest Assembly (x1)
• A: Left Armrest Frame (installed)
• B: Right Armrest Frame (installed)

Hardware Used:

• K: M6 × 45 Bolts
• M: M6 × 60 Bolts
• O: M6 Washers
• N: M6 Nuts
• R: Large Spacers

Instructions:

1. Position the Seat & Backrest Assembly (E) between the Left (A) and Right (B) Armrest Frames.
2. Align the upper mounting holes of Part E with the upper holes on Armrest Frame A.
3. Insert Bolt K (M6 × 45) through the aligned holes.
4. Place Washer O and insert Spacer R as shown in the diagram.
5. Tighten lightly to secure the upper section.
6. Align the lower mounting holes of Part E with the lower side frame holes.
7. Insert Bolt M (M6 × 60) through the aligned holes.
8. Add Washer O and secure with Nut N.
9. Repeat the same process on the opposite side.
10. Once all bolts are inserted, fully tighten all hardware evenly.

Usage Guidelines

• Place on a flat, even surface.
• Avoid aggressive rocking.
• Do not stand on the chair.
• Keep fingers clear of pivot joints.

Care & Maintenance

• Clean frame with mild soap and water.
• Wipe mesh fabric with a damp cloth.
• Inspect pivot points regularly.
• Retighten hardware monthly.
• Store indoors during winter months if possible.
• Use a protective cover when not in use.

Troubleshooting Guide

Issue	Possible Cause	Solution
Uneven gliding	Uneven ground	Move to flat surface
Squeaking noise	Loose bolts	Retighten hardware
Stiff movement	Missing spacer	Check P, Q, R spacers
Wobbling	Uneven tightening	Tighten evenly

Assembly Completion

Once all bolts are securely tightened and the gliding motion operates smoothly, your Outsunny Glider Chair is ready for use.

For technical support, replacement parts, or product questions, you can reach out any time. Thank you!

FAQs