Bring modern style and smart organization to your space with the HOMCOM 3-Tier Storage Shelf. Featuring staggered dividers and a rustic brown finish, it provides ample room for books, décor, and essentials while enhancing any living room, office, or playroom.
Safety & Caution
- Read instructions before assembly and keep for future use.
- Assemble on a flat surface, two adults recommended.
- Secure to wall with the anti-toppling device.
- Do not climb or overload (110 lbs total, 11 lbs per shelf).
- Keep small parts away from children.
- Avoid heat, moisture, and direct sunlight.
- Wipe with a soft, damp cloth only.
Before You Begin
Carefully check all parts and hardware before starting assembly.
PARTS LIST
| No. | Qty | Size (mm) |
| ① | 1 | 945 × 300 |
| ② | 1 | 945 × 300 |
| ③ | 1 | 1000 × 300 |
| ④ | 1 | 1000 × 300 |
| ⑤ | 1 | 945 × 299 |
| ⑥ | 1 | 945 × 299 |
| ⑦ | 4 | 305 × 298 |
| ⑧ | 1 | 270 × 284 |
| ⑨ | 1 | 945 × 60 |
| ⑩ | 1 | 955 × 280 |
HARDWARE LIST
| Code | Qty |
| A | 40 |
| B | 36 |
| D | 4 |
| M | 4 |
| T | 40 |
| W | 1 |
Assembly Instructions for HOMCOM 3-Tier Rustic Brown Storage Shelf
Follow the steps below to assemble the HOMCOM 3-Tier Rustic Brown Storage Shelf (SKU: 838-098) correctly and securely.
Step 1: Assemble ⑤, ⑥ and ⑧
You will need:
- Parts: ⑤, ⑥, ⑧
- Hardware: A × 4, B × 4, T × 4
Instructions:
- Place ⑤ and ⑥ parallel on a flat surface.
- Insert ⑧ vertically between them, aligning all pre-drilled holes.
- Insert A and B through the marked positions to connect ⑤ and ⑥ with ⑧.
- Tighten the fittings evenly and lock them with T.
- Ensure the structure stands firm and panels are flush before continuing.
Step 2: Attach ⑦ Panels Between ⑤ and ⑥
You will need:
- Parts: ⑤, ⑥, ⑦ × 4, ⑧
- Hardware: A × 8, B × 8, T × 8
Instructions:
- Take the structure from Step 1 (⑤, ⑥, ⑧ assembled).
- Align the four ⑦ panels vertically between ⑤ and ⑥ as shown.
- Insert A and B through each connection point to secure the ⑦ panels.
- Place T into the fittings to lock them in place.
- Make sure all ⑦ panels stand straight and evenly spaced before tightening fully.
Step 3: Attach ① and ②
You will need:
- Parts: ①, ②
- Hardware: A × 8, B × 8, T × 8
Instructions:
- Take the structure assembled in Step 2.
- Position ② at the bottom and ① at the top as shown.
- Align all pre-drilled holes carefully with the connecting panels (⑤, ⑥, ⑦, ⑧).
- Insert A and B at each connection point to fix ① and ② securely.
- Lock each joint using T to ensure stability.
- Confirm that all panels are perfectly aligned before tightening completely.
Step 4: Attach ④ and ⑨
You will need:
- Parts: ④, ⑨
- Hardware: A × 10, B × 8, T × 10
Instructions:
- Position ④ on the right side of the assembled structure.
- Align all pre-drilled holes of ④ with the connecting points on ①, ②, ⑤, ⑥, and ⑦.
- Attach ⑨ along the bottom front edge, aligning it with ② and ④.
- Secure both ④ and ⑨ using A and B at each joint.
- Insert T to lock the fittings in place.
- Tighten all screws evenly and make sure the unit is fully aligned and stable.
Step 5: Attach ⑩
You will need:
- Part: ⑩
Instructions:
- Use the assembled structure from Step 4.
- Insert ⑩ from the side as shown by the arrow.
- Slide ⑩ fully into position between ①, ②, ⑤, ⑥, and ⑨.
- Make sure ⑩ is aligned evenly on all sides.
- Press firmly so that ⑩ fits flush and the structure remains square and stable.
Step 6: Attach ③
You will need:
- Part: ③
Hardware: A × 10, B × 8, T × 10
Instructions:
- Position ③ on the left side of the assembled structure.
- Align the holes on ③ with those on ①, ②, ⑤, ⑥, ⑦, and ⑨.
- Insert A and B into the marked holes to connect ③ with the structure.
- Place T into each joint and tighten to secure all fittings.
- Check that ③ is properly aligned and the entire structure is stable.
Step 7: Install M and D
You will need:
- Hardware: M × 4, D × 4
Instructions:
- Place the assembled unit so the back side is facing you for easy access.
- Position M at the indicated locations as shown in the diagram.
- Fasten each M securely using D and a screwdriver.
- Ensure all M fittings are properly aligned and tightened.
- These fittings will keep the unit stable and safely anchored.
Final Step: Install W
You will need:
- Hardware: W × 1
Instructions:
- Place the assembled unit in its final position against the wall.
- Align W at the upper back edge of the structure as shown.
- Secure W to the wall using suitable screws and anchors.
- Tighten all screws and ensure the unit is firmly fixed.
- Check that the structure is level and stable before use.
Maintenance And Care
- Wipe with a soft, dry cloth to remove dust.
- Avoid using harsh chemicals or abrasive cleaners.
- Keep the unit dry and away from direct sunlight or humidity.
- Check and tighten fittings periodically to maintain stability.
Assembly Complete
Your unit is now fully assembled and safely fixed for everyday use.
User Guide
Download the HOMCOM 3-Tier Rustic Brown Storage Shelf Manual (SKU: 838-098) PDF for your reference.
FAQs
1. What should I do if some holes do not line up during assembly?
Loosen the nearby screws slightly and realign the parts without forcing them. Make sure dowels or connectors are fully seated in their holes. Once aligned, tighten all fittings evenly to secure the structure.
2. How can I fix it if one side appears higher than the other after completion?
Place the unit on a flat, level surface and check each leg or corner. Loosen the lower side slightly, adjust the balance, then retighten. Ensure the fittings underneath are evenly tightened for proper alignment.
3. What if a screw or fitting becomes stripped while tightening?
Stop turning immediately to avoid further damage to the hole. Remove the screw and insert a slightly larger one or use a wood filler. Allow it to dry, then reinstall carefully with moderate pressure.
4. Why does the structure wobble slightly after assembly?
Check that all screws and fittings are tightened securely and evenly. Uneven flooring can cause wobbling, so test the unit on a level surface. If needed, use the wall fittings provided to anchor the unit for stability.
5. What can I do if a panel surface gets scratched during setup?
Clean the area with a dry cloth to remove any dust. Use a furniture touch-up pen or wax stick that matches the color. Buff gently until the surface looks smooth and uniform.