The Outsunny Raised Garden Flower Bed Kit with Greenhouse (SKU-845-670) combines a sturdy raised planting box with a transparent protective cover to create a compact, efficient growing system. Designed for balconies, patios, or backyards, this unit provides ample space for vegetables, herbs, and flowers while protecting them from wind, pests, and temperature changes. The greenhouse-style cover improves germination and plant growth by maintaining warmth and moisture.

Tools Recommended

• Phillips Screwdriver
• Rubber Mallet
• Wrench or Spanner
• Protective Gloves

Estimated Assembly Time: 45:60 minutes
Recommended People: 2 adults

Parts List

Safety Instructions

• Assemble the greenhouse on a flat, clean, and stable surface.
• Do not confuse similar screws; identify each using the parts list.
• Avoid overtightening screws, as this may strip threads or damage the plastic frame.
• Keep children and pets away during assembly.
• Use hand tools only unless otherwise stated.
• Avoid assembling in windy or wet conditions.
• Periodically check and retighten screws to maintain long-term stability.

Assembly Overview

Follow the illustrated steps when you are going to assemble your Outsunny Raised Garden Flower Bed Kit with Greenhouse. Below is a step summary for clarity:

Step 1: Assemble the Base Frame

• Connect two Side Panels (b) with two End Panels (c) to form a rectangular base.
• Secure the corners using 4 × Screws (① : M4 × 30 mm).
• Ensure the panels are aligned correctly before tightening the screws.
• Attach the Base Frame (C) in position as shown in the diagram.
• Keep all screws slightly loose until the frame is fully squared, then tighten evenly.

Step 2: Attach the Second Side Frame

• Align the second set of Side Panels (b) with the End Panels (c) to form the opposite side of the raised bed.
• Use 4 × Screws (① : M4 × 30 mm) to secure the joints as shown.
• Ensure the Base Frame (C) is positioned vertically between both side structures.
• Check that all corners are flush and aligned before tightening the screws.
• Leave connections slightly loose until the entire frame is squared, then fully tighten.

Step 3: Secure the Upper Frame Panels

• Align and place the Upper Frame Bars (e) on top of the assembled base structure.
• Fasten each corner connection using 8 × Screws (① : M4 × 30 mm) as shown.
• Ensure all bars are flush with the lower frame before tightening.
• Tighten screws evenly on all four corners to stabilize the rectangular frame.
• Re-check alignment , the frame should be level and square for proper fit in later steps.

Step 4: Install the Inner Panels

• Place the Bottom Panels (a) inside the assembled frame.
• Align the Side Panels (d) securely against the inner edges of the frame.
• Use 12 × Screws (② : M4 × 20 mm) to fix all panels firmly in position.
• Make sure the panels sit flush within the frame without gaps.
• Double-check that all screws are evenly tightened for stability and balance.

Step 5: Reinforce Side and Bottom Panels

• Ensure all Bottom Panels (a) and Side Panels (d) are properly aligned within the frame.
• Fasten the panels securely using 12 × Screws (② : M4 × 20 mm) as shown in the diagram.
• Tighten each screw evenly around all sides to ensure the frame is firm and stable.

Step 6: Confirm the Completed Planter Box

• Ensure all panels and frame connections are securely tightened.
• Check that the side panels and corner posts are aligned evenly and free from gaps.
• Inspect the upper and lower beams for level balance across all sides.

Step 7: Attach the Greenhouse End Panels

• Position both End Panels (A) vertically at each end of the assembled garden bed.
• Align the frame edges of the End Panels (A) with the side beams (B) as shown.
• Secure each panel using 4 × Screws (① : M4 × 30 mm), two on each side.
• Ensure the panels are aligned evenly with no gaps between the joints.

Step 8: Secure the Top Side Beams

• Position the Top Beams (B) across both sides of the greenhouse frame, connecting the upper edges of the end panels (A).
• Align the beams so that they sit flush with the top edge of the frame.
• Fasten securely using 4 × Screws (① : M4 × 30 mm) as shown in the diagram.
• Check that both beams are level and evenly aligned across the structure.

Step 9: Install the Roof Frame and Locking Handles

• Position the Roof Frame (C) at the top of the structure, aligning it with the upper beams.
• Secure the roof frame in place using 5 × Screws (① : M4 × 30 mm) along the top connections.
• Attach the Locking Handles (F) to both sides using 2 × Screws (② : M4 × 20 mm).
• Ensure the handles are aligned properly and can move freely to open or secure the roof.

Step 10: Attach the Roof Panels

• Position both Roof Panels (E) on top of the greenhouse frame (C).
• Align each panel evenly, ensuring the edges sit securely within the upper frame structure.
• Fasten both panels in place using 2 × Screws (② : M4 × 20 mm) as shown.
• Verify that the panels open and close smoothly without obstruction.

Step 11: Attach the Roof Hinges

• Position the Hinges (D) along the inner edge of the Roof Panels (E), aligning them with the upper frame.
• Secure each hinge using 8 × Screws (③ : M3 × 8 mm) as shown in the diagram.
• Make sure the hinges are evenly spaced for smooth, balanced roof operation.
• Tighten all screws firmly to ensure the roof panels pivot securely when opened or closed

Final Step: Assembly Complete

• Carefully place the assembled greenhouse frame onto the raised garden bed as shown in the illustration.
• Ensure all corners and edges align properly so the structure sits securely on the base.
• Double-check that the roof panels open and close smoothly, and the locking handles function correctly.
• Verify all screws are tight and the frame stands level and stable on the ground.

Usage Tips

• Keep the zippered door open during warm days for proper ventilation.
• Use the raised bed for vegetables, herbs, and flowers that benefit from warmth.
• Water plants gently to avoid disturbing the soil near the edges.
• During windy weather, anchor the greenhouse to prevent tipping.
• Clean the cover regularly to allow maximum sunlight.

Maintenance & Care

• Inspect all connectors and screws regularly; tighten if needed.
• Clean panels using mild soap and water only,avoid abrasive cleaners.
• Remove snow or heavy rain accumulation from the cover to prevent sagging.
• Store the greenhouse cover indoors during extreme winter weather to extend its lifespan.
• Avoid placing sharp objects near the cover to prevent tears.

Ready for Use

Congratulations! Your Outsunny Raised Garden Flower Bed Kit with Greenhouse is now ready to use. The combination of a durable raised planter and a clear greenhouse cover helps regulate temperature, retain moisture, and protect your plants from harsh weather.

You can also download the full Outsunny Raised Garden Flower Bed Kit with Greenhouse Manual(PDF) for future reference.

Still need help?

If you have any questions or encounter difficulties during assembly, please contact Aosom’s Customer Support for assistance.

FAQs

1. How can I keep the raised garden bed frame square while tightening all screws?

Assemble loosely first, then measure both diagonals of the frame. Adjust slightly until they match, ensuring it’s perfectly squared before fully tightening the screws. This prevents twisting or gaps later.

2. What if a screw hole doesn’t align with the panel of a raised garden bed?

Loosen nearby connections slightly to relieve tension on the frame. This usually allows the misaligned hole to fall into place. Avoid drilling new holes, as this can weaken the structure.

3. Can I use a power drill to speed up the assembly process of raised garden beds?

Hand tools are strongly recommended. If you use a power drill, set it to a low torque setting to prevent overtightening or stripping screw threads, especially on plastic or aluminum parts.

4. What should I do if the roof panels of a raised garden bed  don’t open smoothly after assembly?

Check the hinge screws and ensure they’re evenly tightened. If they feel too tight, back them off by half a turn; this allows the panels to pivot freely without stressing the frame.